BATHROOM REMODELING / GREATER ATLANTA

Tub to Shower Conversion in Marietta and Atlanta, GA

A custom tub-to-shower conversion in Greater Atlanta typically runs $4,000 to $10,000 as a combined labor-and-materials planning estimate and takes five to eight working days.

We do not drop a plastic liner over old, tired tile. We take the tub and shower area down to the studs and subfloor: the old tub comes out, we adapt the drain, install a brand-new shower valve, build a properly sloped and waterproofed shower pan, and finish the walls with real tile.

Prudencio Renovations is a Georgia licensed residential contractor (RBCO008765), fully insured, and based right here in Marietta.

Request a Free Quote
Tub to walk-in shower conversion, after renovation (comparison 35)

Plan your tub-to-shower conversion

$4,000–$10,000

Typical shower-focused total-project planning range, including labor and homeowner-purchased materials. It is not Prudencio’s labor quote; conditions and selections affect the final cost.

5–8 working days

A typical working-time estimate for the shower itself. Waterproofing cure and tile work can be the longest stretch; the actual schedule depends on the project.

You choose the materials

Homeowners purchase all materials. Prudencio helps with selection and provides labor-only proposals; we do not supply materials.

What Actually Changes When the Tub Comes Out

Taking out a tub is not just a surface swap—it is a full rebuild from the plumbing up. Here is what happens once the demolition is done:

01 Adapt the drain

Tub and shower drains can differ in size and location. We inspect your existing plumbing and adapt the drain size and location to match your new shower layout—whether you choose a traditional center drain, an offset drain, or a sleek linear drain.

02 Install the shower valve

A 20-year-old tub valve is usually near the end of its life, and since we already have the wall open, replacing it now saves you from tearing into new tile later. We install a new pressure-balanced shower valve—and if you want extras like a handheld wand or rain head, we plumb in a diverter at the same time.

03 Build the shower slope and waterproof pan

Water needs a precise pitch to drain completely without pooling. We build the shower floor using either a traditional hand-packed mud bed or a pre-sloped Schluter-KERDI shower tray, tying the waterproofing membrane directly into the drain flange so the entire pan is watertight.

04 Finish the walls

We never put tile over standard drywall or slap up thin plastic panels. We install proper waterproof backer board (such as Schluter-KERDI-BOARD or cement board with a waterproofing membrane) and set your custom tile cleanly from floor to ceiling.

Custom Tile vs. Acrylic & Composite Walls

Many “one-day bath” companies pitch acrylic or composite wall systems as a quick fix. While plastic panels go up fast, they sit over your framing like a shell—and over time, caulk lines can fail, panels can flex, and the bathroom can look like a temporary insert rather than a true remodel.

When we build a custom tiled shower, we inspect the wood framing behind the old tub, fix any hidden water damage, and build a solid, permanent structure. Real porcelain or natural stone tile offers a solid feel and lasting appeal, and it can add value to your home.

Not sure which route makes sense for your budget and long-term plans? Read our full breakdown:

Acrylic vs. Real Tile: Which Shower System Is Right for Your Home?

Shower under construction with red waterproof membrane beside a white tub.

BEHIND THE TILE / BUILT WITH CARE

THE DETAILS YOU DON'T SEE MATTER

Why Waterproofing Is the Part That Decides the Job

Tile and grout alone do not make a shower waterproof—what sits behind the tile is what protects your home from leaks, rot, and mold.

Even the best-looking tile job can fail prematurely if water gets behind the walls or seeps under the shower pan. That is why we treat waterproofing as the most important step of the entire conversion. Every corner, screw penetration, niche, and drain connection is sealed and tested before a single piece of tile goes on the wall. When you invest in a custom shower, you should never have to worry about what is happening behind the walls.

What Drives the Price

The $4,000–$10,000 range is a combined labor-and-materials planning estimate, not a Prudencio labor quote. Normal room conditions and mid-grade finishes are assumed; hidden damage, layout changes and premium selections can change costs.

Tile choice

Classic porcelain subway or field tile versus large-format slabs or natural stone.

Shower glass

A standard framed sliding door versus custom heavy frameless glass (which we template and measure after the tile is finished).

Drain type and layout

Keeping a standard point drain versus reworking floor joists for a linear drain or curbless entry.

Plumbing updates

How much copper or PEX piping needs to be moved inside the wall to fit your new valve and shower heads.

Do You Need a Permit?

Moving a drain and replacing a shower valve generally requires a plumbing permit in Cobb County and surrounding metro cities. Pulling a permit and passing inspection protects your home, ensures everything meets Georgia code, and prevents headaches when you sell your house later. As a licensed residential contractor, we handle the permit process under our license whenever the scope of work requires it.

Considering a curbless shower?

A curbless option may use recessed subfloor panels rather than raising the entire floor. The $2,000–$5,000 upgrade range is a combined labor-and-materials planning estimate, not a labor quote; feasibility depends on the framing and drain.

Explore curbless showers

Questions Homeowners Ask

Can you keep the tub and add a separate shower?

Only if the bathroom is large enough for both. A standard hall bathroom often does not have enough floor space. In a larger primary bathroom, however, we can often reconfigure the layout to fit both a freestanding tub and a walk-in shower.

How long will we be without the bathroom?

Most tub-to-shower conversions take five to eight working days from demolition to final grout. The longest stretches are waiting for waterproofing materials to cure, setting the tile, and letting grout cure properly.

Will the shower floor need to be raised?

Sometimes. The finished floor height depends on your subfloor framing, drain location, and the pan system we use. If you want a curbless (zero-entry) shower, we can often recess the subfloor panels rather than raising the rest of your bathroom floor. Ask us about our curbless shower method, which typically adds $2,000–$5,000 to the combined labor-and-materials project estimate, depending on framing; Prudencio's quote covers labor only.

See tub-to-shower conversions we have built

Explore completed Prudencio projects across the Atlanta area.

Thinking About Losing the Tub?

Tell us your bathroom size and what kind of floor you have (slab or crawlspace/basement). We will walk you through what the conversion takes, give you an honest price range, and let you know if a curbless shower is possible. You purchase the materials; our written quote covers labor only.

Request a Free Quote