CURBLESS SHOWER INSTALLATION · GREATER ATLANTA

Curbless Shower Installation

A curbless shower creates a flush entry without a curb to step over. Framing, drainage and finished floor heights—not the room below—determine how it is built.

Based in Marietta and serving Greater Atlanta. Georgia residential contractor license RBCO008765; fully insured.

Request a labor-only quote
Freestanding tub beside a walk-in shower with rainfall head and body jets, with a white vanity nearby.

A completed Prudencio shower project

How we build a curbless shower without compromising the joists

We never make out-of-code cuts or notches in floor joists to fit a shower. Our usual approach lowers supported subfloor panels between the joists, keeping the structural joists intact. The assembly must suit the actual framing and applicable code and product instructions; where an engineered detail is required, we obtain one rather than improvise.

1. Check framing, drain and floor heights

We check the joist layout, existing subfloor, drain and trap location, and surrounding floor assembly. Tile, setting materials and waterproofing all affect the finished entry height.

2. Recess the subfloor

We remove the subfloor in the shower area and install supported replacement panels at the planned recessed height. This makes room for the tray without shaving down the joists.

3. Install the sloped shower tray

In most cases, a Schluter prefabricated tray provides built-in slope and integrated KERDI waterproofing under the tile. The compatible tray and drain need a properly prepared, supported substrate.

4. Complete waterproofing connections

The tray is only part of the system. The drain connection, seams, corners, wall-to-floor junctions and bathroom floor transition must be sealed using details appropriate to the products installed.

5. Test, tile and check the entry

After waterproofing and required cure time, we water-test as required before tiling, finish the entry and check drainage. The slope, glass layout and showerhead position are planned together to manage splash.

Read Schluter’s recessed shower floor guidance for manufacturer information on recessed floors, waterproofing and point- or linear-drain options. The right detail depends on the products and framing in your bathroom.

See the installation beneath the tile

These construction-stage photographs show the Prudencio team’s Alpharetta project—not stock illustrations. The completed assembly must still be checked.

Plywood subfloor with a vertical PVC pipe and exposed wall studs.

Supported recessed subfloor panels and drain rough-in before the tray.

Orange shower pan on a subfloor with a level across its drain opening.

The sloped Schluter tray set within the recessed shower footprint.

Bathroom subfloor and walls with waterproofing materials beneath a shuttered window.

Sheet membrane at the tray and adjacent floor during waterproofing.

See the Alpharetta project

Can a curbless shower be built over a garage?

Yes. A garage below does not rule it out. We evaluate floor structure, pipe routing, finished heights and access. If work affects the garage ceiling, its required fire separation must be maintained or restored. Any ceiling access or repair is explained in the scope.

What the curbless upgrade costs

$2,000–$5,000 is a general planning range for the curbless upgrade compared with an otherwise similar shower—not the total cost of the shower or bathroom.

Recessed-floor preparation, tray and drain selection, waterproofing transitions and access affect the final cost. Do not add the upgrade again to a package that already includes curbless work.

These figures are combined labor-and-material planning estimates, not Prudencio quotes. Homeowners purchase all materials; Prudencio can help with selection and provides labor-only proposals.

A tub-to-shower conversion is generally planned at $4,000–$10,000 for shower-focused work, including labor and materials. Actual costs depend on the project.

Explore the tub-to-shower service, Atlanta bathroom remodel cost guide and 5×8 bathroom cost breakdown.

Questions about curbless showers

Do you have to cut the joists down?

No. Our usual method recesses supported panels between the joists. Any structural change must follow applicable code, engineered-joist manufacturer requirements and an engineered detail when needed.

Does every curbless shower need a linear drain?

No. Both point and linear drains can work with a compatible sloped tray and the right design. The footprint, plumbing, tile format and floor elevations inform the choice.

Is a curbless shower automatically accessible?

A flush entry removes the curb, but accessibility also depends on opening width, maneuvering space, controls, seating, grab bars and slip-resistant flooring. We plan wheelchair access or aging-in-place needs together.

Can water splash into the bathroom?

Yes, especially in an open shower. Slope, drain placement, waterproofing beyond the entry, showerhead position and glass design help manage it; a curbless entry cannot guarantee water will never escape.

See curbless showers we have built

Explore completed projects across the Atlanta area.

Let’s plan your curbless shower

Tell us your location, room dimensions and what is below the bathroom. We’ll assess the framing and explain the curbless design and labor scope for your home. You purchase the materials; we can help you select them.

Request a quote